Návod k použití SONY SDX-570V annexe 1

[. . . ] 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Mounting Holes . . . . . . . . . . . . . . . . . . . . . . . . 8 Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 9 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 LED Indication for Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Drive Operation . . . . . . . . . . . . . . . . . . . . . . . 12 Emergency Tape Removal Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Interface Implementation . . . . . . . . . . . . . . . . . 16 Supported ATAPI Packet Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Acer Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 VORSICHT Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender / folgenden Umgebung(en): · Wohngegenden · Gewerbegebiete · Leichtindustriegebiete (Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B. ) 2 SDX-570V/R Tape Drive The SDX-570V/R drive is a high capacity data storage device using Advanced Intelligent tape AIT (Advanced Intelligent Tape) technology. Return the switch to its original position to re-enable writing. Using a Cleaning Cassette In case of SDX-570V/R, a cleaning function is built in the drive and hence, a periodic cleaning using cleaning cassette such as other format requires is not necessary. However, when the drive does not recover at the worst case, cleaning cassette is recommended to use. 12 Emergency Tape Removal Procedure 1 2 3 4 5 Remove the drive from the chassis or enclosure to allow access to the bottom and right side of the drive. Locate the small opening in the bottom of the drive and insert the tip of a precision screwdriver so that the Threading motor shaft can be rotated. Rotate the motor shaft counterclockwise to bring the threading mechanism back to the initial position. (Refer to the photo-1 on page 15. ) Before manual eject procedure, tape slack must be removed in order to prevent tape damage. Press and rotate the gear mechanism located on the right side of the drive clockwise to tighten the tape. After the tape slack has been removed, turn the screw located on the right side of the drive clockwise by a precision screwdriver until the tape cartridge is lifted out of the drive mechanism and is ejected. 6 13 7 Return the drive to Acer for repair. 3. Loading Motor 14 A tape guide surface tape guide surface C C B detail A Cartridge Photo-1: The Initial Position of the Threading Mechanism Caution Stop rotating the motor shaft immediately, when the guide B (see detail A of Photo-1) gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise the gear of the drive can be damaged. 15 Interface Implementation Supported ATA Commands ATA commands supported: ­ ATAPI SOFT RESET (0x08) ­ EXECUTE DRIVE DIAGNOSTIC (0x90) ­ ATAPI PACKET COMMAND (0xA0) ­ ATAPI IDENTIFY DEVICE (0xA1) ­ STANDBY IMMEDIATE (0xE0) ­ IDLE IMMEDIATE (0xE1) ­ CHECK POWER MODE (0xE5) ­ SLEEP (0xE6) ­ SET FEATURE (0xEF) Supported ATAPI Packet Commands Mandatory ATAPI command set: Supporting most of all SCSI commands in SDX-400C ­ ERASE ­ INQUIRY ­ LOAD/UNLOAD ­ LOCATE ­ LOG SELECT ­ LOG SENSE ­ MODE SELECT ­ MODE SENSE ­ READ ­ READ POSITION ­ REQUEST SENSE ­ REWIND ­ SPACE ­ TEST UNIT READY ­ WRITE ­ WRITE FILEMARK ­ WRITE BUFFER 16 Specification Product Specifications Dimensions Height Width Depth SDX-570V/R 41. 2 mm (1. 62 in) 149. 0 mm (5. 87 in) 155. 0 mm (6. 1 in) Altitude Operating 0 to 10, 000 feet Vibration Operating Non-Operating Swept Sine 5 to 500 Hz *0. 25 G Peak 1 Octave/min. [. . . ] Loading Motor 14 A tape guide surface tape guide surface C C B detail A Cartridge Photo-1: The Initial Position of the Threading Mechanism Caution Stop rotating the motor shaft immediately, when the guide B (see detail A of Photo-1) gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise the gear of the drive can be damaged. 15 Interface Implementation Supported ATA Commands ATA commands supported: ­ ATAPI SOFT RESET (0x08) ­ EXECUTE DRIVE DIAGNOSTIC (0x90) ­ ATAPI PACKET COMMAND (0xA0) ­ ATAPI IDENTIFY DEVICE (0xA1) ­ STANDBY IMMEDIATE (0xE0) ­ IDLE IMMEDIATE (0xE1) ­ CHECK POWER MODE (0xE5) ­ SLEEP (0xE6) ­ SET FEATURE (0xEF) Supported ATAPI Packet Commands Mandatory ATAPI command set: Supporting most of all SCSI commands in SDX-400C ­ ERASE ­ INQUIRY ­ LOAD/UNLOAD ­ LOCATE ­ LOG SELECT ­ LOG SENSE ­ MODE SELECT ­ MODE SENSE ­ READ ­ READ POSITION ­ REQUEST SENSE ­ REWIND ­ SPACE ­ TEST UNIT READY ­ WRITE ­ WRITE FILEMARK ­ WRITE BUFFER 16 Specification Product Specifications Dimensions Height Width Depth SDX-570V/R 41. 2 mm (1. 62 in) 149. 0 mm (5. 87 in) 155. 0 mm (6. 1 in) Altitude Operating 0 to 10, 000 feet Vibration Operating Non-Operating Swept Sine 5 to 500 Hz *0. 25 G Peak 1 Octave/min. Swept Sine 5 to 500 Hz *0. 5 G Peak 1 Octave/min. 3 axes, 3 directions (A) curve weight 35 db (A) 60 db (A) Acoustic Noise Streaming Write/Read Insert/Eject Note The sound-meter on (A) scale is located 1m in front of the center of the drive front panel. Shock Operating No Data Loss Half Sine Performance 5 G Peak 3 ms 3 axes, 3 directions *Interval 10 seconds No Device Damage Half Sine 90 G Peak 3 ms (30 G Peak 11 ms) 3 axes, 3 directions Non-Operating 17 Temperature and Humidity Range Temperature Operating Non-Operating (mech. ) Non-Operating (tape) Humidity Operating Non-Operating (mech. ) Non-Operating (tape) 20 to 80% RH, non-condensing Maximum wet bulb temperature = 26 °C 5 to 95% RH (T<30%/h) 20 to 80% RH (T<30%/h) 5 °C to 40 °C (T<10 °C/h) ­ 40 °C to 70 °C (T<20 °C/h) ­ 40 °C to 45 °C (T<20 °C/h) Power Requirements Model SDX-570V/R Voltage 5 V +/­ 5 % 12 V +/­ 10 % Max Ripple 100 mVp-p 150 mVp-p Current Typical 1. 4 A 0. 45 A Maximum 2. 5 A 1. 2 A Suspended Particulate Operating Less than 150 microgram/m3 Based Sampling period 24 hours ESD Discharge Voltage < 15 kV: No operation failure < 20 kV: No drive damage Air-cooling Requirement Surrounding temperature < 40 °C Clean air flow is recommended to minimize the possibility of data loss. 18 Acer Contact For further information, please contact: http://csd. acer. com. tw/ 19 This document contains proprietary information which is protected by copyright. [. . . ]