Návod k použití SONY SD

[. . . ] 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SCSI Connection/Setting the SCSI ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting Holes . . . . . . . . . . . . . . . . . . . . . . . . 9 Remodeling from 5. 25" Model to 3. 5" Model . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 9 Remodeling from 5. 25" Model to 3. 5" Model . . . . . . . . . . . . . . . . . . . . . . . 11 Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 LED Indication for Drive Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Drive Operation . . . . . . . . . . . . . . . . . . . . . . . 15 Emergency Tape Removal Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Interface Implementation . . . . . . . . . . . . . . . . . 19 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Acer Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 VORSICHT Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender / folgenden Umgebung(en): · Wohngegenden · Gewerbegebiete · Leichtindustriegebiete (Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B. ) 2 SD Tape Drive The SD drive is a high capacity data storage device using Advanced Intelligent tape AIT (Advanced Intelligent Tape) technology. As the cassette is inserted, the drive takes it and automatically loads it into drive mechanism. Unloading a Tape The cassette can be removed from the SD either in response to a SCSI Unload Command, or by pressing the eject bottom. By pressing Eject button, the tape goes to BOT, the drive unthreads it, and ejects the cassette from the slot. Write-protecting a Tape Cassettes can be write-protected by sliding the tab on the back of the cassette. In this state, data can be read from the tape but not written onto it. AIT-1 Using your fingernail, push the switch in the direction of the arrow to protect the tape from writing or accidental erasure. Return the switch to its original position to re-enable writing. Using a Cleaning Cassette In case of SDX-400, a cleaning function is built in the drive and hence, a periodic cleaning using cleaning cassette such as other format requires is not necessary. However, when the drive does not recover at the worst case, cleaning cassette is recommended to use. 15 Emergency Tape Removal Procedure 1 2 3 4 5 Remove the drive from the chassis or enclosure to allow access to the bottom and right side of the drive. Locate the small opening in the bottom of the drive and insert the tip of a precision screwdriver so that the Threading motor shaft can be rotated. Rotate the motor shaft counterclockwise to bring the threading mechanism back to the initial position. (Refer to the photo-1 on page 18. ) Before manual eject procedure, tape slack must be removed in order to prevent tape damage. Press and rotate the gear mechanism located on the right side of the drive clockwise to tighten the tape. After the tape slack has been removed, turn the screw located on the right side of the drive clockwise by a precision screwdriver until the tape cartridge is lifted out of the drive mechanism and is ejected. 6 16 7 Return the drive to Acer for repair. 3. [. . . ] Press and rotate the gear mechanism located on the right side of the drive clockwise to tighten the tape. After the tape slack has been removed, turn the screw located on the right side of the drive clockwise by a precision screwdriver until the tape cartridge is lifted out of the drive mechanism and is ejected. 6 16 7 Return the drive to Acer for repair. 3. Loading Motor 17 A tape guide surface tape guide surface C C B detail A Cartridge Photo-1: The Initial Position of the Threading Mechanism Caution Stop rotating the motor shaft immediately, when the guide B (see detail A of Photo-1) gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise the gear of the drive can be damaged. 18 Interface Implementation Supported SCSI Messages Abort Bus Device Reset Command Complete Disconnect Extended Message ­ Synchronous Data Transfer Request ­ Wide Data Transfer Request Identify ( w/&w/o Disconnect ) Ignore Wide Residue Message Parity Error Message Reject No Operation Restore Pointers Save Data Pointer Supported SCSI Commands Erase Inquiry Load/Unload Locate Log Sense Log Select Mode Select Mode Sense Prevent Allow Medium Removal Read Read Block Limits Read Buffer Read Position Report Diagnostic Result Release Unit Receive Density Support Report Luns Request Block Address Request Sense Reserve Unit Rewind Seek Block Send Diagnostic Space Test Unit Ready Verify Write Write Buffer Write Filemarks 19 Specification Product Specifications Dimensions Height Width Depth SD 41. 2 mm (1. 62 in) 101. 6 mm (4. 0 in) 155. 0 mm (6. 1 in) SD/R 41. 2 mm (1. 62 in) 149. 0 mm (5. 87 in) 155. 0 mm (6. 1 in) Altitude Operating 0 to 10, 000 feet Vibration Operating Non-Operating Swept Sine 5 to 500 Hz *0. 25 G Peak 1 Octave/min. [. . . ]